will bring you to those results. (iii) T50 When portable tank instruction T50 is indicated in Column (7) of the 172.101 Hazardous Materials Table, the applicable liquefied compressed gas and chemical under pressure descriptions are authorized to be transported in portable tanks in accordance with the requirements of 173.313 of this subchapter. Transportation by vessel in IBCs is prohibited. Decomposition can be initiated by heat, moisture or by impurities (e.g., powdered metals (iron, manganese, cobalt, magnesium)). When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. IBCs are only authorized if approved by the Associate Administrator. The material is also be subject to operational controls which include not exceeding a temperature of 55C (130F) at the time it is offered or during transportation, not exceeding a transportation time of 24 hours, and drivers transporting spent bleaching earth must be trained in the properties and hazards of the spent bleaching earth. When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. N41 Metal construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material. This content is from the eCFR and may include recent changes applied to the CFR. (1) Even though certain packagings are specified in this part, it is, nevertheless, the responsibility of the person offering a hazardous material for transportation to ensure that such packagings are compatible with their lading. Note that batteries utilizing different chemistries (i.e., those battery chemistries specifically covered by another entry in the 172.101 Table) as well as dry batteries with a marked rating greater than 9-volt may not be combined with used or spent batteries in the same package. For UN identification numbers 1327, 1363, 1364, 1365, 1386, 1408, 1841, 2211, 2217, 2793 and 3314, IBCs are not required to meet the IBC performance tests specified in part 178, subpart N, of this subchapter. Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. This entry also applies to articles not conforming to the requirements of 173.302, 173.304, or 173.306 of this subchapter, containing a small pressure receptacle with a release device. See Batteries, dry, sealed, n.o.s. in the 172.101 Hazardous Materials Table (HMT) of this part for transportation requirements for nickel-metal hydride batteries transported by other modes and for nickel-metal hydride button cells or nickel-metal hydride cells or batteries packed with or contained in battery-powered devices transported by vessel. These provisions apply only to transportation by rail. This entry applies to machinery or apparatus containing hazardous materials as a residue or as an integral element of the machinery or apparatus. Prohibited means bottom openings are prohibited, and Prohibited for liquids means bottom openings are authorized for solid material only. B4 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks are not authorized. A Shipper of a hazardous material is responsible for its classification and packaging prior to offering it for shipment to a Carrier. 388 a. Lithium batteries containing both primary lithium metal cells and rechargeable lithium ion cells that are not designed to be externally charged, must meet the following conditions: i. These requirements must be met in addition to the design and construction specifications in part 178 of this subchapter. (eg: b. and are not subject to requirements of this subchapter except for the following: (a) Incident reporting. N36 Aluminum or aluminum alloy construction materials are permitted only for halogenated hydrocarbons that will not react with aluminum. Except when the liquids are fully absorbed in solid material contained in sealed bags, for single packagings, each packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II level. Each empty bottle must have a minimum weight of not less than 140 grams and a minimum wall thickness of not less than 0.020 inch (0.508 mm). 159 This material must be protected from direct sunshine and kept in a cool, well-ventilated place away from sources of heat. Where different hazardous materials in limited quantities are packed together in the same outer packaging, when a gross mass is indicated Column 4 of 173.27 Table 3, the net quantity of each hazardous material must be shown in addition to the gross mass of the completed package. IBCs must be packed in closed freight containers or a closed transport vehicle. b. B28 Packagings must be made of stainless steel. For transportation by aircraft, a telephone report in accordance with 171.15(a) is required if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a dry battery. N92 Notwithstanding the provisions of 173.24(g) of this subchapter, packagings shall be designed and constructed to permit the release of gas or vapor to prevent a build-up of pressure that could rupture the packagings in the event of loss of stabilization. 39 This substance may be carried under provisions other than those of Class 1 only if it is so packed that the percentage of water will not fall below that stated at any time during transport. A82 The quantity limits in columns (9A) and (9B) do not apply to human or animal body parts, whole organs or whole bodies known to contain or suspected of containing an infectious substance. These substances must satisfy the criteria for classification as an ammonium nitrate emulsion of Test Series 8 of the UN Manual of Tests and Criteria, Part I, Section 18 (IBR, see 171.7 of this subchapter), and may not be classified and transported unless approved by the Associate Administrator. d. All inner packagings placed inside bulk outer packagings must be blocked and braced to prevent shifting during transportation that could cause the container to open or fall over. Fertilizers meeting the criteria for this identification number are only subject to the requirements of this subchapter when offered for transportation and transported by air or vessel. If appropriate, a package containing this material must conform to the additional labeling requirements of 172.402 of this subchapter. Examples of such vehicles are electrically-powered cars, motorcycles, scooters, three- and four-wheeled vehicles or motorcycles, trucks, locomotives, bicycles (pedal cycles with an electric motor) and other vehicles of this type (e.g., self-balancing vehicles or vehicles not equipped with at least one seating position), lawn tractors, self-propelled farming and construction equipment, boats, aircraft, wheelchairs and other mobility aids. 2 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone B (see 173.116(a) or 173.133(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. A61 a. The manufacturer must produce technical documentation of the design type, manufacture as well as the tests and their results. B16 The lading must be completely covered with nitrogen, inert gas or other inert materials. (2) An indication of compliance with this special provision must be provided by marking each package with the words not restricted or by including the words not restricted on a transport document such as an air waybill accompanying the shipment. A bulk packaging containing sulfur is not subject to the placarding requirements of subpart F of this part, if it is marked with the appropriate identification number as required by subpart D of this part. Based on the volatility class determined by using ASTM D 439 and the Reid vapor pressure (RVP) of the particular gasoline, the maximum lading pressure and maximum ambient temperature permitted during the loading of gasoline may not exceed that listed in Table I. b. The following tables list, and set forth the requirements of, the special provisions referred to in column 7 of the 172.101 table. c. Completed neutron radiation detection systems containing detectors meeting the conditions of paragraph a of this special provision must be transported as follows: (1) The detectors must be contained in a strong sealed outer casing; (2) The casing must contain include sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents; (3) The completed system must be packed in strong outer packagings capable of withstanding a 1.8 meter (5.9 feet) drop test without leakage unless a system's outer casing affords equivalent protection. For continued use of approvals dated prior to January 1, 2012, see 173.308(b)(5). 31 Materials which have undergone sufficient heat treatment to render them non-hazardous are not subject to the requirements of this subchapter. The material must be packaged so that the percentage of diluent does not fall below that stated in the approval at any time during transportation. (3) A code containing the letter B refers to a special provision that applies only to bulk packaging requirements. Tanks containing solidified methacrylic acid must not be reheated during transport. The mixture for emulsions typically has the following composition: 60-85% ammonium nitrate; 5-30% water; 2-8% fuel; 0.5-4% emulsifier or thickening agent; 0-10% soluble flame suppressants; and trace additives. When column 7 of the Hazardous Materials Table (49 CFR 172.101) includes a special provision code for an entry in the table, the requirement of that code - or codes, there may be several of them - is in addition to the general packaging requirements of 173.24 and any other applicable packaging requirements in Part 173. Heater pipes must be of welded construction designed for a test pressure of 500 psig. Each inner packaging contains not more than 30 mL; b. 34 The commercial grade of calcium nitrate fertilizer, when consisting mainly of a double salt (calcium nitrate and ammonium nitrate) containing not more than 10 percent ammonium nitrate and at least 12 percent water of crystallization, is not subject to the requirements of this subchapter. Energy storage capacity means the energy held by a capacitor, as calculated using the nominal voltage and capacitance. 5 If this material meets the definition for a material poisonous by inhalation (see 171.8 of this subchapter), a shipping name must be selected which identifies the inhalation hazard, in Division 2.3 or Division 6.1, as appropriate. 420 This entry does not apply to manufactured articles (such as table tennis balls). In addition, MC 312 and DOT 412 cargo tank motor vehicles must: c. Have a MAWP or design pressure of at least 87 psig; and. 21 This material must be stabilized by appropriate means (e.g., addition of chemical inhibitor, purging to remove oxygen) to prevent dangerous polymerization (see 173.21(f) of this subchapter). (5) Each receptacle shall be able to withstand a pressure of 20 bar (2000 kPa) without leakage when the pressure relief device is deactivated. When chemical stabilization is employed, the person offering the material for transport shall ensure that the level of stabilization is sufficient to prevent the material as packaged from dangerous polymerization at 50 C (122 F). N87 The use of copper valves on UN pressure receptacles is prohibited. j. Overcharge of the rechargeable lithium ion cells is precluded by design; iii. The lithium batteries must meet the requirements of 173.185(a) and contain the necessary systems to prevent overcharge and over discharge between the batteries. Packages containing mixtures with not less than 90% by mass, of phlegmatizer need not bear a POISON subsidiary risk label. Authorized specification bulk outer packagings are UN11G fiberboard intermediate bulk containers (IBC) and UN13H4 woven plastic, coated and with liner flexible intermediate bulk containers (FIBCs) meeting the Packing Group II performance level and lined with a plastic liner of at least 6 mil thickness. Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 10.34 Bar (150 psig). B46 The detachable protective housing for the loading and unloading valves of multi-unit tank car tanks must withstand tank test pressure and must be approved by the Associate Administrator. Column 7 specifies codes for special provisions applicable to hazardous materials. 3090 or 3091, as appropriate. A hypochlorite solution, UN1791, is a Class 8 corrosive material. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Thickness of stainless steel for portable tank shells and heads must be the greater of 6.35 mm (0.250 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.3 times the vapor pressure of the hazardous material at 46 C (115 F). The identification number used must be consistent on package markings, shipping papers and emergency response information. The caps must not contain more than an average of twenty-five hundredths of a grain of explosive composition per cap; c. The caps must be packed inside packagings constructed of cardboard not less than 0.013-inch in thickness, metal not less than 0.008-inch in thickness, non-combustible plastic not less than 0.015-inch in thickness, or a composite blister package consisting of cardboard not less than 0.013-inch in thickness and non-combustible plastic not less than 0.005-inch in thickness that completely encloses the caps; d. The minimum dimensions of each side and each end of the cardboard packaging must be 1/8th inch in height or more; e. The number of caps inside each packaging must be limited so that not more than 10 grains of explosives composition may be packed into one cubic inch of space, and not more than 17.5 grains of the explosive composition of toy caps may be packed in any inner packaging; f. Inner packagings must be packed in outer packagings meeting PG II performance criteria; g. Toy caps may be packed with non-explosive or non-flammable articles provided the outer packagings are marked as prescribed in this paragraph; h. Toy paper caps of any kind must not be packed in the same packaging with fireworks; i. B52 Notwithstanding the provisions of 173.24b of this subchapter, non-reclosing pressure relief devices are authorized on DOT 57 portable tanks. b. Comments or questions about document content can not be answered by OFR staff. W9 When offered for transportation by water, the following Specification packagings are not authorized unless approved by the Associate Administrator: woven plastic bags, plastic film bags, textile bags, paper bags, IBCs and bulk packagings. The standards for transporting a single bulk hazardous material for blasting by cargo tank motor vehicles (CTMV); and. 41 This material at the Packing Group II hazard criteria level may be transported in Large Packagings. 4 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone D (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. Formaldehyde solutions not containing methanol and not meeting the Class 3 flammable liquid criteria must be described using a different proper shipping name. If a vehicle is powered by a flammable liquid and a flammable gas internal combustion engine, it must be described using Vehicle, flammable gas powered. This includes hybrid electric vehicles powered by both an internal combustion engine and wet, sodium or lithium batteries installed. The material must be loaded dry. Where the subsidiary hazard material is Forbidden in column (9A) or (9B) of the 172.101 Table, the radioactive material may only be offered for transportation and transported by aircraft under conditions approved by the Associate Administrator. For single packagings, each packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II level. (iii) A copy of the test results must be kept on file at each facility where packagings are offered for transportation, and must be made available to a representative of the Department upon request. This entry does not apply to life saving appliances described in 173.219 (UN2990 and UN3072). 196 The nitrocellulose must meet the criteria of the Bergmann-Junk test or methyl violet paper test in the UN Manual of Tests and Criteria, Appendix 10 (IBR, see 171.7 of this subchapter). 109 Rocket motors must be nonpropulsive in transportation unless approved in accordance with 173.56 of this subchapter. 173 For adhesives, printing inks, printing ink-related materials, paints, paint-related materials, and resin solutions which are assigned to UN3082, and do not meet the definition of another hazard class, metal or plastic packaging for substances of packing groups II and III in quantities of 5 L (1.3 gallons) or less per packaging are not required to meet the UN performance package testing when transported: a. TP17 Only inorganic non-combustible materials may be used for thermal insulation of the tank. 335 Mixtures of solids that are not subject to this subchapter and environmentally hazardous liquids or solids may be classified as Environmentally hazardous substances, solid, n.o.s, UN3077 and may be transported under this entry, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. For example, nickel-metal hydride batteries transported by vessel in certain quantities are covered by another entry (see Batteries, nickel-metal hydride, UN3496). Column 8 However, the hazard label corresponding to the hazard class or division may be substituted for the marking. The cargo transport unit shall display the UN number in a manner in accordance with 172.332 of this subchapter and be placarded on two opposing sides. If unlined tanks are washed out with water, they must be repassivated prior to return to service. This training must be documented in training records required by 172.704(d). Additionally, each cylinder must be visually inspected in accordance with CGA pamphlet, CGA C-6 (incorporated by reference, see 171.7). [Amdt. B35 Tank cars containing hydrogen cyanide may be alternatively marked Hydrocyanic acid, liquefied if otherwise conforming to marking requirements in subpart D of this part. B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. 61 A chemical oxygen generator is spent if its means of ignition and all or a part of its chemical contents have been expended. full text search results Wall thickness must be verified ultrasonically at intervals midway between periodic hydraulic tests (every 2.5 years). See UN1210, UN1263, UN1266, UN3066, UN3469, and UN3470. B83 Bottom outlets are prohibited on tank car tanks transporting sulfuric acid in concentrations over 65.25 percent. A200 These articles must be transported as cargo and may not be carried aboard an aircraft by passengers or crewmembers in carry-on baggage, checked baggage, or on their person unless specifically authorized in 175.10. B70 If DOT 103ANW tank car tank is used: All cast metal in contact with the lading must have 96.7 percent nickel content; and the lading must be anhydrous and free from any impurities. B45 Each tank must have a reclosing combination pressure relief device equipped with stainless steel or platinum rupture discs approved by the AAR Tank Car Committee. air bag inflators, air bag modules, seat-belt pretensioners, and pyromechanical devices containing Class 1 (explosive) materials or materials of other hazard classes. TP32 Portable tanks may be used subject to the following conditions: a. Search & Navigation Except as otherwise provided in this subchapter, these special provisions do not apply to UN portable tanks or IBCs: B1 If the material has a flash point at or above 38 C (100 F) and below 93 C (200 F), then the bulk packaging requirements of 173.241 of this subchapter are applicable. Background and more details are available in the site when drafting amendatory language for Federal regulations: TP12 This material is considered highly corrosive to steel. 383 For transportation by motor vehicle, substances meeting the conditions for high viscosity flammable liquids as prescribed in 173.121(b)(1)(i), (b)(1)(ii), and (b)(1)(iv) of this subchapter, may be reassigned to Packing Group III under the following conditions: a. 353 Ammonium permanganate, ammonium permanganate aqueous solutions, and mixtures of a permanganate with an ammonium salt are forbidden for transport. is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (tf) and the maximum mean bulk temperature during transportation (tr) both in degrees celsius. (9) A code containing the letter W refers to a special provision that applies only to transportation by water. Specification 110A500W tanks must be stainless steel. It may be transported on cargo aircraft only with the prior approval of the Associate Administrator. b. Packagings equivalent to DOT 406 cargo tanks are excepted from 178.345-7(d)(5), circumferential reinforcements; 178.345-10, pressure relief; 178.345-11, outlets; 178.345-14, marking, and 178.345-15, certification. A lighter refill exceeding 4 fluid ounces capacity (7.22 cubic inches) or containing more than 65 grams of fuel must be classed as a Division 2.1 material, described with the proper shipping name appropriate for the material, and packaged in the packaging specified in part 173 of this subchapter for the flammable gas contained therein. Orientation markings as described in 172.312(a)(2) are required when liquid hazardous materials may escape due to incorrect orientation. 28 The dihydrated sodium salt of dichloroisocyanuric acid does not meet the criteria for inclusion in Division 5.1 (Oxidizer) and is not subject to the requirements of this subchapter unless meeting the criteria for inclusion in another class or division. These mixtures may be classified in Division 4.1 when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) and approved by the Associate Administrator. Sealed packets and articles containing less than 10 mL of a Class 3 liquid in Packing Group II or III absorbed onto a solid material are not subject to this subchapter provided there is no free liquid in the packet or article. N84 The maximum quantity per package is 500 g (1.1 lbs.). The Packing Group assigned will be II or III, according to the classification criteria for either Class 3 or Division 4.1, as appropriate, applied to the base material. In addition, for solid materials, special provision B54 applies. 53 Packages of these materials must bear the subsidiary risk label, EXPLOSIVE, and the subsidiary hazard class/division must be entered in parentheses immediately following the primary hazard class in the shipping description, unless otherwise provided in this subchapter or through an approval issued by the Associate Administrator, or the competent authority of the country of origin. 79 This entry may not be used for mixtures that meet the definition for oxidizing gas. B10 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks, and DOT 57 portable tanks are not authorized. The proper shipping name Paint related material may be used for consignments of packages containing Paint and Paint related material in the same package; b. A8 For combination packagings, if glass inner packagings (including ampoules) are used, they must be packed with cushioning material in tightly closed metal receptacles before packing in outer packagings. When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. B59 Water-tight, sift-proof, closed-top, metal-covered hopper cars are also authorized provided that the lading is covered with a nitrogen blanket. N78 Packages consisting of inner glass, earthenware, or polyethylene or other nonfragile plastic bottles or jars not over 0.5 kg (1.1 pounds) capacity each, or metal cans not over five pounds capacity each, packed in outer wooden boxes, barrels or kegs, or fiberboard boxes are authorized and need not conform to the requirements of part 178 of this subchapter. Column 5 references applicable requirements for bottom openings in part 178 of this subchapter. A combination packaging consisting of a 4G fiberboard box with inner receptacles of glass or earthenware; b. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. Uranium hexafluoride may be classified under this entry only if the conditions of 173.420(a)(4) and (6) and (d) and 173.421(b) and (d) of this subchapter, and, for fissile-excepted material, the conditions of 173.453 of this subchapter are met. (2) A code containing the letter A refers to a special provision which applies only to transportation by aircraft. 102 The ends of the detonating cord must be tied fast so that the explosive cannot escape. B135 For Large Packagings offered for transport by vessel, flexible or fibre inner packagings shall be hermetically sealed. Radiation detection systems containing such detectors are not subject to any other requirements of this subchapter provided they are packed in accordance with paragraph c of this special provision. Column 7 specifies codes for special provisions applicable to hazardous materials. 164 Substances must not be transported under this entry unless approved by the Associate Administrator on the basis of the results of appropriate tests according to Part I of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). 387 When materials are stabilized by temperature control, the provisions of 173.21(f) of this subchapter apply. B85 Cargo tanks must be marked with the name of the lading in accordance with the requirements of 172.302(b). (3) B codes. will bring you directly to the content. Packagings of other material constructed with a small amount of metal must be designed such that the hazardous material does not contact the metal. (contains magnesium, magnesium nitrides) in PG II or III may be packaged in sift-proof bulk packagings that prevent liquid from reaching the hazardous material with sufficient venting to preclude dangerous accumulation of flammable, corrosive or toxic gaseous emissions such as methane, hydrogen and ammonia. Each transport unit must be leakproof when used as bulk packaging. package). e. When offered for transport in an ammonia dispenser, the receptacles shall be connected to the dispenser in such a way that the assembly is guaranteed to have the same strength as a single receptacle. If a tank car tank is equipped with a non-reclosing pressure relief device, the rupture disc must be perforated with a 3.2 mm (0.13 inch) diameter hole. If you work for a Federal agency, use this drafting Each tank must be equipped with pressure relief devices conforming to the following requirements: 1 Total venting capacity in standard cubic feet hour (S.C.F.H.) These entries include hybrid electric vehicles powered by both an internal combustion engine and batteries. Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner. The chemical under pressure must be classed based on the hazard characteristics of the components in the propellant; the liquid; or the solid. (i) Tests must be performed on each type and size of bottle, for each manufacturing location. 115 Boosters with detonator, detonator assemblies and boosters with detonators in which the total explosive charge per unit does not exceed 25 g, and which will not mass detonate and undergo only limited propagation in the shipping package may be assigned to 1.4B classification code. Regulation Y c. The motor carrier must maintain a satisfactory safety rating as prescribed in 49 CFR part 385. Comparative fire testing between a package as prepared for transport (including the substance to be transported) and an identical package filled with water must show that the maximum temperature measured inside the packages during testing does not differ by more than 200 C (392 F). caila clause supernanny now, picture of monty williams' wife,
When Does Kings Island Open In 2022,
Lauren Mcbride Husband,
Crime Map Near Milan, Metropolitan City Of Milan,
Justise Winslow Hip Replacement Surgery,
Articles C